14 Common Misconceptions Concerning Double Glazing Door Lock Repairs
14 Common Misconceptions Concerning Double Glazing Door Lock Repairs
Blog Article
Double Glazing Door Lock Repairs
Is your uPVC window or door mechanism broken? Perhaps the door or window handles aren't aligned properly or are difficult to use.
You'll be wasting energy if your double-glazed doors don't work properly. This also increases the risk of burglary. Owen the Locksmith will be able to fix your door lock at a reasonable cost.
Snapped Key
When a key snaps off inside a lock, it could be extremely difficult. This can also be a security problem, as it may leave you vulnerable to an intruder if the door does not lock. There are fortunately quick fixes you can attempt to fix the issue and get your door functioning correctly.
The first step is to remain calm. If you panic you may end up pushing the broken key piece further into the lock.
Then spray WD-40 or a different penetrating oil into the lock to help the broken piece slide out more easily. You can also use the screwdriver to break any pieces stuck. If you're lucky enough to have a little bit of the key hanging out and you want to remove it, make use of a paperclip, or any other thin metal object to grab it and remove it. Both methods are effective, but you need to be careful not to push the broken key piece further into the keyway.
Some paperclips have grooved edges that can be used as hook extractors and Jigsaw blades also work for this use. If you don't happen to have one of these tools you can bend a hook with needle-nosed pliers. You can also make use of a pair of tweezers to grasp and pull out the remaining pieces of broken keys.
If you can't get the broken piece of the key out, try using a lock de-icer. It is available at most hardware stores, and it is used to freeze any water or ice that could be inside the lock.
If none of these strategies seem to be helping, it might be time to call locksmith. The experts at Fitlocks can quickly fix problems such as broken handles and broken keys with uPVC locks and door mechanisms. They can also alter your double glazing door mechanisms to allow them to operate more easily. Book a double glazing repair with us online, or give us a phone call to discuss your needs.
Broken Cylinder
A damaged cylinder could pose an extremely risky security issue. A professional locksmith is able to fix the cylinder. Locksmiths will need to tap the cylinder to fix it. They can do this with the hammer or any other tools, but the most effective method is to use a long match or a piece of wire. Then, position the match's tip or wire in the keyway. The locksmith can then strike the lock to break it. This is much safer than using a hammer that could harm the lock.
The most frequent cause for cracks in the head of a cylinder is due to overheating. This can occur when the block and the cylinder head are made of various metals like cast-iron and aluminum. Different metals will be heated and cool at different rates. This can cause localised hotspots to expand quicker than the rest of the cylinder.
Another possible cause for cylinder cracks is corrosion. If the cylinder block and head are not maintained correctly, they can rust or corrode and cause them to expand faster than they would normally. In time, this could also cause cracks.
If your uPVC door or window lock is stiff or requires a lot of pressure to website turn, this can be caused by several things. A faulty locking mechanism, misalignment or the wear of the handle are typical causes of this issue.
It is a quick and inexpensive fix that most homeowners with double glazing can perform. A professional locksmith should be able solve this issue within a matter of hours after arriving at your residence. They can repair the locking mechanisms, or replace the window handles and replace the gearboxes based on your particular requirements. A locksmith with experience will always be able to advise you on the most cost-effective options for your home. They can even recommend upgrades to the highest-security 3 Star euro cylinders TS007 that provide an extra layer of protection against burglars. It is a small cost to pay for the peace-of-mind that comes from knowing your uPVC here door is secure.
Broken Handle
Window handle locks have complex mechanisms that deteriorate with time and use, so it's not a surprise they occasionally break. If yours fails it's difficult to pinpoint the cause of the issue. Make sure you fix it correctly.
Fixing your broken handle, regardless of whether it's the internal latch or locking mechanism can increase the security of your uPVC door and prevent draughts. It is costly to repair or replace your handle if it is not double glazed near me done correctly and could also harm the frame and the lock of your door.
Screwdriver When the window is open remove the screw that holds the handle. The screw should be on the inside of the back plate, which is usually concealed by a screw cover for aesthetic reasons. Be careful not to lose any internal components inside the handle, such as the plates or levers on either side of the spindle. Ideally, keep them in the same order so you can replace them in the event of a need.
Then, rotate the handle until it's 90 degrees to the window frame and loosen the screw at the back of the handle that holds it to the internal spindle by using another screwdriver. Once this is loose, you should be in a position to pull the handle off and take out the broken spindle. Replace it with a new spindle, ensuring it's the same length (you can buy them on the internet or at hardware stores). Securely screw it in the correct position. Be careful not to tighten too much because this could cause damage to the handle more info or the window frame.
Check that the new handle is installed Close the window and test the handle. It should work smoothly and you'll be able to open your window once more.
Don't forget to double-check that your uPVC window is shut properly when you're working with the handle. If they're not then you may experience draughts and damp in your home as in addition to compromising the energy efficiency of your home. A local window company, like Core Sash Windows, will be capable of adjusting the hinges on your window frames so they are able to shut properly.
Broken Spindle
It is usually the case that the spindle inside the handle breaks, rather than the handle itself. This is most common in uPVC tilt and turn windows. These types of windows require a handle that operates a locking mechanism in the window frame. The handle is attached a central rod that activates a series of locks that are shaped like mushrooms and secure the window frame keep. If the dead latch mechanism is not able to open when the handle is turned it is likely that the spindle has broken This can be a frustrating problem.
Fortunately there are steps that can be taken to rectify this issue. A professional locksmith can quickly and efficiently repair this problem. A reputable locksmith will be able to disassemble the window's handle using a tool that removes the wheel portion that houses the spindle. This can be done without damaging the handle or causing other damage to the window frame.
Once the wheel has been removed the technician can then examine the spindle to determine what caused it to break. This involves disassembling the spindle and examining each component, noting any damage or excessive wear. This process is usually carried out by technicians working in a clean and safe environment.
The next step is to clean the damaged spindle, this helps eliminate any dirt or debris that might be obstructing its normal functioning. The spindle could be repaired or replaced. If the technician is replacing the spindle, it is replacement double glazing units near me possible to use a dowel that is similar in size to the original. Then, he will make holes in the same way into both pieces. This will ensure that the spindle is perfectly matched with the handle.
If the spindle that is damaged is beyond repair, it could be necessary to replace it entirely. Home centers sell generic replacements however if your window design is unique then you'll need to contact a cabinet maker or woodworker who can make the exact piece. After the spindle is installed, it can be fixed to the handle. Line up the screw holes on the handle with the screws that are already in the frame. Once the new handle is installed, you are now ready to operate your uPVC window.